Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: A simple fiberglass question
By:Etienne Muller
Date: 12/13/2013, 4:54 am
In Response To: Re: Strip: A simple fiberglass question (Greg Galloway)

Since you only have two squeegees, do you clean them between batches? How do you keep epoxy from building up on them and fouling the surface?

Just give them a wipe down after a glassing session with a rag. The tile squeegee with the rubbery tip will last for a boat or too, but there is nothing like a new tile squeegee.

With the stiff plastic ones, I find it useful to give the tip a rub with fine water paper on a flat surface, just to get any manufacturing burrs off it.

If you have not done it before, glassing seems like a daunting and complex process, with all the instruction that can go with it, but if your preparation is right, (warm room, warm resin, all your tools ready before hand, etc) and you follow a definite process, (one squeeze alternately from each pump so that you don't loose count and get a wrong mix, sufficient stirring, working along for a while, then going back to finish saturated sections, reducing temps as you go along, etc), then it is actually quite enjoyable: a milestone in the project.

As long as you get the resin out of the cup fairly soon, you have more time than you may think to spread it evenly and move along.

Before you start, tell everyone that until they see you again you are incommunicado. Then be phlegmatic about it and don't start with a sense of urgency or panic. If you watch Nick's videos on glassing you will notice that he is half asleep during the job, or maybe he uses that alone time for meditation.

Et

Messages In This Thread

Strip: Finished inlay, ready for glass! *PIC*
Greg Galloway -- 12/8/2013, 10:31 pm
Re: Strip: Finished inlay, ready for glass!
M Hammond -- 12/9/2013, 12:32 am
Re: Strip: Finished inlay, ready for glass!
Bill Hamm -- 12/9/2013, 1:03 am
Re: Strip: Finished inlay, ready for glass!
Etienne Muller -- 12/9/2013, 2:39 am
Re: Strip: Finished inlay, ready for glass!
John Messinger -- 12/9/2013, 7:07 am
How did you do it?
jay Babina -- 12/9/2013, 8:40 am
Re: How did you do it?
Greg Galloway -- 12/9/2013, 11:01 am
Dan's "Queen of my Heart"
Greg Galloway -- 12/9/2013, 11:12 am
Re: Dan's "Queen of my Heart"
Dan Caouette (CSCWC) -- 12/11/2013, 9:17 am
Re: How did you do it?
Marc Upchurch -- 12/9/2013, 4:27 pm
Re: How did you do it?
Don T. -- 12/9/2013, 4:45 pm
Re: How did you do it?
Etienne Muller -- 12/9/2013, 5:39 pm
Thanks for posting that series
Jay Babina -- 12/10/2013, 8:42 am
Re: Thanks for posting that series
Greg Galloway -- 12/10/2013, 9:18 am
Re: Thanks for posting that series
Kurt Maurer -- 12/10/2013, 8:45 pm
Re: Thanks for posting that series
Greg Galloway -- 12/10/2013, 9:55 pm
Strip: A simple fiberglass question
Greg Galloway -- 12/11/2013, 9:59 pm
Re: Strip: A simple fiberglass question
Bill Hamm -- 12/12/2013, 1:28 am
Re: Strip: A simple fiberglass question *PIC*
Etienne Muller -- 12/12/2013, 7:15 am
Re: Strip: A simple fiberglass question
Etienne Muller -- 12/12/2013, 7:20 am
Re: Strip: A simple fiberglass question
Greg Galloway -- 12/12/2013, 8:52 pm
Re: Strip: A simple fiberglass question
Etienne Muller -- 12/13/2013, 4:54 am
Re: Strip: A simple fiberglass question
wysedav -- 12/12/2013, 9:08 pm
Re: Strip: A simple fiberglass question
Bill Hamm -- 12/13/2013, 10:15 am
Re: Strip: A simple fiberglass question
Etienne Muller -- 12/13/2013, 1:49 pm
Re: Strip: A simple fiberglass question
JohnAbercrombie -- 12/13/2013, 6:33 pm
Re: Strip: A simple fiberglass question
Etienne Muller -- 12/13/2013, 7:07 pm
Re: Strip: A simple fiberglass question
Bill Hamm -- 12/15/2013, 12:33 am
Re: Strip: A simple fiberglass question
Bill Hamm -- 12/15/2013, 12:30 am
Re: Strip: Finished inlay, ready for glass!
Greg Galloway -- 12/20/2013, 7:23 pm
Re: Strip: Finished inlay, ready for glass! *PIC*
Etienne Muller -- 12/21/2013, 12:44 pm
Re: Strip: Finished inlay, ready for glass!
Greg Galloway -- 12/21/2013, 6:26 pm
Re: Strip: Finished inlay, ready for glass!
Marc Upchurch -- 12/21/2013, 7:00 pm
Re: Strip: Finished inlay, ready for glass!
Bill Hamm -- 12/22/2013, 12:17 am
Re: Strip: Finished inlay, ready for glass!
Etienne Muller -- 12/22/2013, 5:23 am
Re: Strip: Finished inlay, ready for glass!
Bill Hamm -- 12/23/2013, 12:02 am
Re: Strip: Finished inlay, ready for glass!
Etienne Muller -- 12/23/2013, 5:22 am
Re: Strip: Finished inlay, ready for glass!
Greg Galloway -- 8/24/2014, 10:55 am
Re: Strip: Finished inlay, ready for glass!
Marc Upchurch -- 8/24/2014, 11:39 am
Re: Strip: Finished inlay, ready for glass!
Greg Galloway -- 8/24/2014, 12:20 pm