Re: Thanks everyone, this ought to work ...
By:Kurt Loup, Baton Rouge
Date: 2/6/2003, 4:49 pm
Date: 2/6/2003, 4:49 pm
In Response To: Thanks everyone, this ought to work ... *LINK* (Pascal, in Chile)
: I like that insert idea. There is some 6mm MDF lying around in my shop. I can
: probably rout a hole with a shoulder into my 15mm melamine, and install
: the mdf flush with the tabletop. That will bring the router 9mm closer to
: the wood strips. Maybe I will fix it in some fancy way to be able to lift
: the insert out.
If you cut out a shoulder for the insert, which is what I did, don't worry about getting it the exact depth. I cut it deeper than needed and added deck/drywall screws in each corner that can be adjusted to level the insert with the top of the router table.
Kurt
Messages In This Thread
- Strip: trouble with b&c routing
Pascal, in Chile -- 2/6/2003, 10:21 am- Re: Strip: trouble with b&c routing
David Hanson -- 2/6/2003, 4:40 pm- b&c vs bevel
mike allen -- 2/7/2003, 9:13 pm
- Re: Strip: trouble with b&c routing
Mike Loriz -- 2/6/2003, 3:12 pm- Re: Strip: trouble with b&c routing *LINK* *Pic*
Kurt Loup, Baton Rouge -- 2/6/2003, 1:49 pm- Thanks everyone, this ought to work ... *LINK*
Pascal, in Chile -- 2/6/2003, 3:30 pm- Re: Thanks everyone, this ought to work ...
Kurt Loup, Baton Rouge -- 2/6/2003, 4:49 pm
- Re: Thanks everyone, this ought to work ...
- Re: Strip: trouble with b&c routing
Paul J -- 2/6/2003, 1:40 pm- Re: Strip: trouble with b&c routing *Pic*
Chip Sandresky -- 2/6/2003, 12:18 pm- Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 1:04 pm- Re: Strip: trouble with b&c routing
Chip Sandresky -- 2/6/2003, 2:16 pm
- Re: Strip: trouble with b&c routing
- Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/6/2003, 11:39 am- Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 12:56 pm- Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/7/2003, 6:22 am- My turn for a stupid question....
Bob Deutsch -- 2/7/2003, 12:06 pm- Re: My turn for a stupid question....
Kent LeBoutillier -- 2/7/2003, 9:42 pm
- Re: My turn for a stupid question....
- If I might explain beveling
Paul G. Jacobson -- 2/7/2003, 12:20 am- Re: If I might explain beveling
Bob Deutsch -- 2/7/2003, 4:29 am- Re: If I might explain beveling
Jack Sanderson -- 2/7/2003, 10:31 am- Thanks Sam & Jack! *NM*
Bob Deutsch -- 2/7/2003, 12:08 pm
- Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 10:30 am- Re: If I might explain beveling
Mike Loriz -- 2/7/2003, 7:57 pm- Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 11:17 pm
- Re: If I might explain beveling
- Re: If I might explain beveling
Mark Normand -- 2/7/2003, 7:11 am - Thanks Sam & Jack! *NM*
- Re: If I might explain beveling
- I second Tim's question...thanks Kent... *NM*
Bob Deutsch -- 2/6/2003, 3:19 pm- Re: I second Tim's question...thanks Kent...
Don Lucas -- 2/7/2003, 9:28 am
- My turn for a stupid question....
- Re: Strip: trouble with b&c routing
- b&c vs bevel
- Re: Strip: trouble with b&c routing