Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: trouble with b&c routing
By:Tim Eastman
Date: 2/6/2003, 12:56 pm
In Response To: Re: Strip: trouble with b&c routing (Kent LeBoutillier)

O-kay Kent, I'm going to reveal my ignorance here.

Can you describe to a complete newbie what a rolling bevel butt joint is? Are you planing your edges to each other as you lay on your stripps?? Apparently from your experience this presents you with tighter joints once all fairing and sanding is done?

Tim Eastman

(snip)
: You might want to consider using rolling bevel but joints and forget the cove
: and bead. I no longer use cove and bead and in my opinion the final
: outcome is much tighter looking joints. I found that with cove and bead I
: ended up planing off the edge of the cove during fairing which makes the
: joint show much more.

Messages In This Thread

Strip: trouble with b&c routing
Pascal, in Chile -- 2/6/2003, 10:21 am
Re: Strip: trouble with b&c routing
David Hanson -- 2/6/2003, 4:40 pm
b&c vs bevel
mike allen -- 2/7/2003, 9:13 pm
Re: Strip: trouble with b&c routing
Mike Loriz -- 2/6/2003, 3:12 pm
Re: Strip: trouble with b&c routing *LINK* *Pic*
Kurt Loup, Baton Rouge -- 2/6/2003, 1:49 pm
Thanks everyone, this ought to work ... *LINK*
Pascal, in Chile -- 2/6/2003, 3:30 pm
Re: Thanks everyone, this ought to work ...
Kurt Loup, Baton Rouge -- 2/6/2003, 4:49 pm
Re: Strip: trouble with b&c routing
Paul J -- 2/6/2003, 1:40 pm
Re: Strip: trouble with b&c routing *Pic*
Chip Sandresky -- 2/6/2003, 12:18 pm
Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 1:04 pm
Re: Strip: trouble with b&c routing
Chip Sandresky -- 2/6/2003, 2:16 pm
Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/6/2003, 11:39 am
Re: Strip: trouble with b&c routing
Tim Eastman -- 2/6/2003, 12:56 pm
Re: Strip: trouble with b&c routing
Kent LeBoutillier -- 2/7/2003, 6:22 am
My turn for a stupid question....
Bob Deutsch -- 2/7/2003, 12:06 pm
Re: My turn for a stupid question....
Kent LeBoutillier -- 2/7/2003, 9:42 pm
If I might explain beveling
Paul G. Jacobson -- 2/7/2003, 12:20 am
Re: If I might explain beveling
Bob Deutsch -- 2/7/2003, 4:29 am
Re: If I might explain beveling
Jack Sanderson -- 2/7/2003, 10:31 am
Thanks Sam & Jack! *NM*
Bob Deutsch -- 2/7/2003, 12:08 pm
Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 10:30 am
Re: If I might explain beveling
Mike Loriz -- 2/7/2003, 7:57 pm
Re: If I might explain beveling
Sam McFadden -- 2/7/2003, 11:17 pm
Re: If I might explain beveling
Mark Normand -- 2/7/2003, 7:11 am
I second Tim's question...thanks Kent... *NM*
Bob Deutsch -- 2/6/2003, 3:19 pm
Re: I second Tim's question...thanks Kent...
Don Lucas -- 2/7/2003, 9:28 am