Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Weights...design question
By:Ben Staley
Date: 6/25/2001, 1:03 pm
In Response To: Re: Weights (Shawn Baker)

Hey Shawn, question for you.
I was thinking about weight per linear foot on a kayak, a foot of boat in the center weighs a lot more than a foot at the ends....fatter. Do you know if you get the same performance advantages by adding the length at the ends? If I remember correctly, you added another middle form? or maybe added an inch between every form.
What if I left the 4 forms in the middle alone and spaced the end ones out 2 inches further? Would I end up with a longer boat with all of the advantages but without as much additional weight? Of course the cockpit area would remain the same and the large foot challenged among us would still need to raise the deck a little.

Just thinking, no plans for a G-18 yet :)

: I got cheated! ;) With seat and compass, it's 48#. Mine isn't the 'L'
: version, though--it's 18' long, and as deep as the L, but only 21"
: wide.

: 6 oz. glass inside and out, hull and deck, double on the bottom of the hull,
: and inside the cockpit. 1/4-" cedar, redwood, pine.

: Epoxy application makes a huge difference. I have a 57-lb. Chesapeake 17 with
: half as much glass as the Guillemot.

: Shawn

Messages In This Thread

Guillemot "L" Launch *Pic*
Dave Seales -- 6/24/2001, 11:40 pm
Re: Guillemot "L" Launch
Roger Nuffer -- 6/25/2001, 3:39 pm
Great looking boat/design! *NM*
Bob Deutsch -- 6/25/2001, 2:48 pm
Re: Guillemot "L" Launch
Ben Staley -- 6/25/2001, 10:33 am
Re: Great Job! It's a fun boat *NM*
Shawn Baker -- 6/25/2001, 10:26 am
Nice Job
David Hanson -- 6/25/2001, 9:49 am
Re: Nice Job
Dave Seales -- 6/25/2001, 12:17 pm
Re: Nice Job
David Hanson -- 6/25/2001, 3:41 pm
Re: Nice Job
LeeG -- 6/28/2001, 8:30 pm
how transparent was the dynel
mike allen ---> -- 6/25/2001, 5:32 pm
Fairly clear *Pic*
David Hanson -- 6/26/2001, 9:36 am
Re: how transparent was the dynel
David Hanson -- 6/25/2001, 5:44 pm
Re: Vacuum-Bagging Dynel
Shawn Baker -- 6/25/2001, 4:06 pm
An idea for you
Brian Nystrom -- 6/25/2001, 5:22 pm
Re: An idea for you
Bruce Schultz -- 6/26/2001, 9:51 am
Re: Vacuum-Bagging Dynel
David Hanson -- 6/25/2001, 4:23 pm
Re: Vacuum-Bagging Dynel
Shawn Baker -- 6/25/2001, 4:31 pm
Re: Weights
Shawn Baker -- 6/25/2001, 12:36 pm
Re: Weights...design question
Ben Staley -- 6/25/2001, 1:03 pm
Re: Save weight with materials/methods, not size
Shawn Baker -- 6/25/2001, 4:29 pm
Re: Save weight with materials/methods, not size
Ben Staley -- 6/25/2001, 5:00 pm
Re: Save weight with materials/methods, not size
Tom -- 6/26/2001, 1:41 pm
Re: Save weight with materials/methods, not size
LeeG -- 6/26/2001, 2:40 pm
Re: Save weight with materials/methods, not size
Tom -- 6/27/2001, 9:43 am
Re: Save resistance with optimum hull design
Shawn Baker -- 6/27/2001, 11:23 am
a problem w/ matching resin/glass wt?
mike allen ---> -- 6/25/2001, 6:15 pm
Re: Weights...design question
Shawn Baker -- 6/25/2001, 4:02 pm
Re: Weights...design question
Paul G. Jacobson -- 6/25/2001, 3:59 pm
Re: Weights
Dave Seales -- 6/25/2001, 12:52 pm