Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: THAT explains it!
By:Spidey
Date: 3/31/2000, 12:48 am
In Response To: Re: cove and bead (Paul G. Jacobson)

Hi Paul;

%$%-@!xx! - Why didn't you post this BEFORE I cut my strips? !$#&!*! The ends of the cedar boards ARE weathered differently than the stuff an inch from the end - - This has to stand as one of the most important tips for ripping strips for all time! Why didn't I think of that? I wondered why, at the 11th hour, I had color variations at the butt joints that shouldn't have been there. Sure, it wets out and looks like it's going to be OK now, but it would have saved a lot of needless sanding and frustration in the interim. And, it would probably blend more perfectly anyway if the ends are removed.

Paul's Best Tip Ever (as near as I can tell) needs restating : Before you ever even attempt to rip strips from a board, crosscut 1" from each end of the board and discard.

Thanks for a belated great tip, Spidey

Messages In This Thread

cove and bead
Butch -- 3/30/2000, 3:17 pm
Grain and single scarfing
mike allen ---} -- 3/31/2000, 4:11 pm
Re: cove and bead
Nick Schade - Guillemot Kayaks -- 3/31/2000, 8:49 am
Re: cove and bead
Edgar Kleindinst -- 3/31/2000, 7:34 am
Re: cove and bead
Kent LeBoutillier -- 3/31/2000, 6:20 am
Re: scarf splicing strips
Dave Houser -- 3/31/2000, 1:57 am
Re: scarf splicing strips
Walter H. Klaus -- 4/2/2000, 8:54 am
Sanding disk
Paul G. Jacobson -- 4/2/2000, 6:46 pm
Re: Sanding disk
Walter H. Klaus -- 4/3/2000, 9:44 pm
Re: Sanding disk
John B. -- 4/2/2000, 7:28 pm
Re: Sanding disk
Paul G. Jacobson -- 4/3/2000, 1:13 pm
Re: Sanding disk
John B. -- 4/3/2000, 7:22 pm
Re: Table Saw Sanding disk Source
Dave Houser -- 4/2/2000, 9:35 pm
Re: Table Saw Sanding disk Source
John B. -- 4/3/2000, 7:48 am
Re: scarf jig
Don Beale -- 3/31/2000, 12:13 pm
Re: scarf jig
Spidey -- 3/31/2000, 3:14 pm
Re: scarf jig
Don Beale -- 4/1/2000, 1:27 am
Re: scarf jig
Spidey -- 4/1/2000, 2:07 am
Re: scarfing jig
Hank -- 3/31/2000, 9:33 am
Re: cove and bead
Paul G. Jacobson -- 3/30/2000, 11:37 pm
Re: THAT explains it!
Spidey -- 3/31/2000, 12:48 am
Re: THAT explains it!
Hank -- 3/31/2000, 9:25 am
Actually, it is more like this
Paul G. Jacobson -- 3/31/2000, 4:42 am
Re: cove and bead
Eric Schade (shearwater Boats) -- 3/30/2000, 7:36 pm
Re: cove and bead
Dean Trexel -- 3/30/2000, 5:13 pm
Re: cove and bead
Vaclav Stejskal -- 3/30/2000, 4:34 pm