Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Best sanding practices
By:dave g
Date: 2/27/2012, 10:09 pm
In Response To: Re: Strip: Best sanding practices (Mike Bielski)

: I use a couple different sizes/stiffnesses. I put good handles on
: them, usually wooden cabinet knobs/pulls. But here are the
: things I think are important- I line the surface of the board
: with cork gasket-making material, like you can get from auto
: parts stores. I glue that on with Super 77, then I attach
: sandpaper with Artist's Repositionable Spray Adhesive. As long
: as you don't put your board away with paper stuck to it it will
: come off just fine. If it doesn't hit it with a heat gun for a
: minute or two. Adding the cork gives it a little bit of padding
: so that the edges don't dig in as easily.

: m

I just use a durablock gives the same result just done for you.

Dave g

Messages In This Thread

Strip: Best sanding practices
Robert l -- 2/24/2012, 12:03 am
Re: Strip: Best sanding practices
Jon Mortimer -- 2/24/2012, 6:39 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/24/2012, 9:13 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/24/2012, 7:07 am
Re: Strip: Best sanding practices
Eric Mattison -- 2/24/2012, 7:26 pm
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 2:20 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/25/2012, 9:21 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/25/2012, 12:54 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/26/2012, 1:10 am
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 6:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/26/2012, 8:58 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/26/2012, 12:46 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/26/2012, 1:10 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:05 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 10:49 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:37 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/28/2012, 1:47 pm
Re: Strip: Best sanding practices
Etienne Muller -- 2/28/2012, 1:51 pm
Re: Strip: Best sanding practices
Justin -- 2/29/2012, 5:29 am
Re: Strip: Best sanding practices
Kirk Fredericks -- 2/29/2012, 5:22 pm
Re: Strip: Best sanding practices
ancient kayaker -- 2/27/2012, 11:16 pm
Re: Strip: Best sanding practices
dave g -- 2/28/2012, 12:42 am
Re: Strip: Best sanding practices
ancient kayaker -- 2/28/2012, 10:37 am
Re: Strip: Best sanding practices
Bill Hamm -- 2/28/2012, 1:40 am
Re: Strip: Best sanding practices
george jung -- 2/28/2012, 12:01 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/29/2012, 1:48 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/28/2012, 3:48 am
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/27/2012, 11:08 am
Re: Strip: Best sanding practices
John Abercrombie -- 2/27/2012, 1:03 pm
Re: Strip: Best sanding practices
Rob Macks/Laughing Loon CC&K -- 2/28/2012, 4:15 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:41 pm
Re: Strip: Best sanding practices
Dan Caouette (CSFW) -- 2/27/2012, 11:55 am
Re: Strip: Best sanding practices
Mike Bielski -- 2/27/2012, 7:56 pm
Re: Strip: Best sanding practices
dave g -- 2/27/2012, 10:09 pm
Re: Strip: Best sanding practices
Bill Hamm -- 2/27/2012, 2:02 am
Re: Strip: Best sanding practices
Scott Fitzgerrell -- 2/27/2012, 11:56 am
Re: Strip: Best sanding practices
Ian Johnson -- 2/26/2012, 6:37 pm