Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: scarf jig
By:Bill Hamm
Date: 11/30/2008, 1:24 am
In Response To: scarf jig (bill stupak)

: I clamp the pieces to the jig for cutting, but I have had a couple of drop
: offs go flying because they were not stopped by the fence. The next time I
: use it I was planning to clamp a board to extend the fence on the right
: side of the blade to eliminate that problem. I do see your point of
: cutting out knots in the middle of piece, on the miter saw I would have to
: do that in another setup.

: Bill

That's why my jig has supports on both sides of the piece to be cut, can be clamped above the cut too. Wastes a little wood, but it's better than launching the ends.

Bill H.

Messages In This Thread

Tools: Scafing jig for table saw *Pic*
Kudzu -- 11/25/2008, 6:45 pm
Re: Tools: Scafing jig for table saw
Terry Haines -- 6/3/2009, 10:56 pm
Re: Tools: Scafing jig for table saw
dsmithla -- 6/4/2009, 5:56 pm
Re: Tools: Scarfing jig for table saw
Terry Haines -- 6/4/2009, 6:56 pm
Re: Tools: Scarfing jig for table saw
Davd S. -- 6/5/2009, 10:51 am
Re: Tools: Scarfing jig for table saw
Bill Hamm -- 6/5/2009, 10:53 am
Re: Tools: Scarfing jig for table saw
Davd S. -- 6/5/2009, 11:18 am
Re: Tools: Scarfing jig for table saw
Bill Hamm -- 6/5/2009, 11:33 am
Re: Tools: Scafing jig for table saw
Jay Babina -- 6/3/2009, 7:51 pm
Re: Tools: Scafing jig for table saw
Kudzu -- 6/4/2009, 9:36 pm
Scafing jig WARNING
Kudzu -- 6/3/2009, 12:51 pm
Re: Scafing jig WARNING
Aaron H -- 6/4/2009, 11:03 am
Re: Scafing jig WARNING
Don Lucas -- 6/4/2009, 9:16 am
Re: Scafing jig WARNING
John F Monroe -- 6/5/2009, 5:11 am
Re: Scafing jig WARNING
Bill Hamm -- 6/3/2009, 3:19 pm
Re: Scafing jig WARNING
Kudzu -- 6/3/2009, 4:40 pm
Re: Scafing jig WARNING
Clayton Plunkett -- 6/3/2009, 5:06 pm
Re: Scafing jig WARNING
Kudzu -- 6/4/2009, 9:24 pm
Re: Scafing jig WARNING
Clayton Plunkett -- 6/5/2009, 10:22 am
Re: Scafing jig WARNING
Greg H- -- 6/5/2009, 9:09 am
A different interpretation
Glenn -- 6/5/2009, 2:47 am
Re: Scafing jig WARNING
Bill Hamm -- 6/4/2009, 9:49 pm
Re: Tools: Scafing jig for table saw *Pic*
bill stupak -- 11/27/2008, 10:27 am
Re: Tools: Scafing jig for table saw
Scott Fitzgerrell -- 6/4/2009, 12:22 pm
Re: Tools: Scafing jig for table saw *LINK*
bill stupak -- 6/5/2009, 12:46 pm
Re: Tools: Scafing jig for table saw
Scott Fitzgerrell -- 6/5/2009, 6:02 pm
Re: Tools: Scafing jig for table saw
Kudzu -- 6/6/2009, 8:54 am
Re: Tools: Scafing jig for table saw *LINK*
bill stupak -- 6/5/2009, 12:47 pm
Re: Tools: Scafing jig for table saw
Kudzu -- 11/29/2008, 9:15 am
scarf jig
bill stupak -- 11/29/2008, 11:30 am
Re: scarf jig
Bill Hamm -- 11/30/2008, 1:24 am
Re: scarf jig
Tom Raymond -- 12/3/2008, 3:22 pm
Re: scarf jig
Bill Hamm -- 12/3/2008, 4:01 pm
Re: Tools: Scafing jig for table saw
Aaron H -- 11/26/2008, 10:12 am
Re: Tools: Scafing jig for table saw
Kudzu -- 11/26/2008, 10:53 am
Re: Tools: Scafing jig for table saw
Aaron H -- 11/26/2008, 1:34 pm
Re: Tools: Scafing jig for table saw
Kudzu -- 11/26/2008, 8:13 pm
Re: Tools: Scafing jig for table saw
Paul Montgomery -- 11/26/2008, 10:47 pm
Re: Tools: Scafing jig for table saw
Kudzu -- 11/27/2008, 8:00 am
Re: Tools: Scafing jig for table saw *Pic*
Paul Montgomery -- 11/27/2008, 9:33 am
Re: Tools: Scafing jig for table saw
Kudzu -- 11/29/2008, 9:23 am
Re: Tools: Scafing jig for table saw
Bill Hamm -- 11/27/2008, 8:53 am
Yet another photo *NM* *Pic*
Kudzu -- 11/25/2008, 6:46 pm
What's the ratio on the scarf?
Brian Nystrom -- 11/26/2008, 10:14 am
Re: What's the ratio on the scarf?
Kudzu -- 11/26/2008, 10:49 am
Re: Yet another photo
Danper -- 11/25/2008, 9:41 pm
Re: Yet another photo
Kudzu -- 11/25/2008, 11:00 pm
another photo *NM* *Pic*
Kudzu -- 11/25/2008, 6:45 pm