Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Routing w/ Tablesaw
By:mike allen ---}
Date: 2/16/2000, 10:08 pm
In Response To: Re: Hollow shaft (Shawn Baker)

? Do you think making a square hollow and coring it with polystyrene foam
> would be a viable option? Would the foam provide enough structural support
> to prevent failure in a diagonally (diagonal to the 4 sides of the
> ?box? shaft) loaded situation?

? Just trying to figure out an option besides buying a router!

? Shawn

I guess if you were Joe Pro you could raise the blade to say 3/4 the ht of the teeth and put the fence at an angle so if you sighted at the angle the blade would cut an oval the ht set and the width of the offset. Carefully raise the blade say 3/4 the tooth ht. for each pass ( 1/16 in to 1/8 in) would give an elliptical groove.

-mick (ps - I'm not gonna try it)

Messages In This Thread

Paddle-building pages (Dean - don't read)
Ross Leidy -- 2/16/2000, 12:35 pm
Re: Paddle-building pages (Dean - don't read)
Dennis -- 2/16/2000, 2:21 pm
Re: no books, but...
Ross Leidy -- 2/17/2000, 10:48 pm
Re: Paddle-building pages
Shawn Baker -- 2/16/2000, 1:27 pm
Re: Paddle-building pages
Chris Casazza -- 2/17/2000, 8:58 am
Hollow shaft
Nick Schade - Guillemot Kayaks -- 2/16/2000, 3:33 pm
Re: Hollow shaft
Chris Luneski -- 2/19/2000, 6:03 am
Re: Hollow shaft
Mike Hanks -- 2/19/2000, 3:14 pm
Re: Hollow shaft
Chris Luneski -- 2/21/2000, 4:12 am
Re: Hollow shaft
Bill Heuser -- 2/24/2000, 5:16 pm
Re: Hollow shaft
Robert Woodard -- 2/24/2000, 6:26 pm
Re: Hollow shaft
Shawn Baker -- 2/16/2000, 4:10 pm
Re: Hollow shaft
Nick Schade - Guillemot Kayaks -- 2/17/2000, 9:18 am
Molding Planes
Paul Lund -- 2/18/2000, 5:14 am
Routing w/ Tablesaw
mike allen ---} -- 2/16/2000, 10:08 pm
Re: Routing w/ Tablesaw
Shawn Baker -- 2/17/2000, 9:52 am
Re: weight saving with hollow shaft?
Hank -- 2/16/2000, 10:37 pm
Re: weight saving with hollow shaft?
John D. -- 2/17/2000, 1:54 am
Re: weight saving with hollow shaft?
Bram -- 2/17/2000, 11:57 am
Is the weight saving worth it?
Shawn Baker -- 2/17/2000, 10:13 am
Re: thanks for the "numbers"
Hank -- 2/17/2000, 7:48 am
Even thinner/lighter
Shawn Baker -- 2/17/2000, 10:19 am
Re: Even thinner/lighter
Bram -- 2/17/2000, 11:43 am
Re: Even thinner/lighter
Will Brockman -- 2/18/2000, 1:56 pm
Re: Even thinner/lighter
Ross Leidy -- 2/17/2000, 10:26 am
Re: Even thinner/lighter
Shawn Baker -- 2/17/2000, 10:29 am
Re: weight saving with hollow shaft?
Spidey -- 2/17/2000, 12:49 am
Re: Hollow shaft
Bram -- 2/16/2000, 6:46 pm
Re: Hollow shaft
Mike Hanks -- 2/16/2000, 5:37 pm