Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: 2 X 4 's into strips
By:Bill Hamm
Date: 1/3/2017, 11:54 pm
In Response To: Strip: 2 X 4 's into strips (Richard Mertins)

Well personally I'd rip the 2x4's into 3/4" thick strips 2" wide then rip them into strips. Lots less cutting and lots less waste. Remember that every cut on a table saw generates at least 1/8" of waste turned into saw dust with a thin kerf blade, you can lose a lot of wood that way.

Btw, grain orientation is pretty much up to you, it looks pretty and looks like a wood boat but the wood is mostly just a core for the fiberglass.

Bill H.

Messages In This Thread

Strip: 2 X 4 's into strips
Richard Mertins -- 1/3/2017, 6:41 pm
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/3/2017, 8:36 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/3/2017, 11:54 pm
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/4/2017, 7:52 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/4/2017, 9:53 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 11:07 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/4/2017, 11:59 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 12:56 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/5/2017, 12:23 am
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/5/2017, 7:05 am
Overthinking
Curtis Fisher -- 1/5/2017, 8:16 pm
Re: Overthinking
Steve Solomon -- 1/6/2017, 12:12 am
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/6/2017, 3:12 am
Re: Strip: 2 X 4 's into strips
David Wyse -- 1/4/2017, 12:01 pm
Re: Strip: 2 X 4 's into strips
Steve Solomon -- 1/4/2017, 9:22 am
Re: Strip: 2 X 4 's into strips
Nick R. -- 1/4/2017, 4:18 pm
Re: Strip: 2 X 4 's into strips
Rob Macks/Laughing Loon CC&K -- 1/5/2017, 9:06 am
Re: Strip: 2 X 4 's into strips
JohnAbercrombie -- 1/7/2017, 11:16 am
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/7/2017, 11:34 am
Re: Strip: 2 X 4 's into strips
Rob Macks/Laughing Loon CC&K -- 1/7/2017, 11:50 am
Re: Strip: 2 X 4 's into strips
Richard Mertins -- 1/8/2017, 7:32 am
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/8/2017, 8:55 am
Re: Strip: 2 X 4 's into strips
dave koslow -- 1/9/2017, 2:11 pm
Re: Strip: 2 X 4 's into strips
Marc Upchurch -- 1/9/2017, 5:18 pm
Re: Strip: 2 X 4 's into strips
Bill Hamm -- 1/9/2017, 1:20 am