Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Cutting strips- Time Lapse
By:Nick Schade - Guillemot Kayaks
Date: 12/4/2014, 6:36 pm
In Response To: Re: Strip: Cutting strips- track saw v table saw *PIC* (Nick Schade - Guillemot Kayaks)

I've been cutting strips.

Like Rob says, setting up a power feed does take some time. One way to deal with that is to do a lot of strips in a batch. I've got 3 classes scheduled for next year, plus some building projects and making some extra for future reference. Below is a time lapse of cutting about 3 kilometers of strips.

Setting up the power feed took about 15 minutes to bolt the unit in place and adjust it. I run a few pieces of scrap wood through to dial in the set up and make sure the thickness is good.

The first set of strips in the video are from 3/4" blanks cut from 2-by stock. As Rob suggests there is some very nice wood available if you don't limit yourself to flat-grained boards. Ripping blanks from thicker material and then rotating to cut the strips provides vertical grained strips.

I found some nice flat grained "inland" red cedar which at my supplier comes as flat grained boards. These are edge ripped.

I am keeping my strips in order. Some boards screwed to saw horses create a good staging table to organize the strips as they are cut. Stretch wrap bundles the cut strips back into a set.

Again like Rob, I like the Rigid "Flip Top" feed stands. My saw horses and work tables are all designed to be the same height as my table saw so I have a lot of in/out feed options, but the lightweight FlipTops are nice. The top can be set to tilt down to help catch drooping strips, it then flips up to get it to the right height. This is much better than roller stands which tend to steer the end of your board causing all sorts of problems. The flat plastic top of the FlipTops are slippery and allow the boards to do their thing,

Let me say that a power feed is a luxury. I don't recommend it for everyone. They can be hard to set up right. I've grooved my share of rollers, but even hand feeding strips has a learning curve. My mind tends to wander while doing boring tasks so I feel the feed gives me a welcome degree of safety.

And with over 10,000 linear feet of strips cut in the past couple days I cut one 18 foot strips wrong. The rest are dead on accurate.

Related to using a smaller saw. I recently decided that I didn't need a 52" side extension table. I found a cast iron side extension on eBay and sawed my fence locking rail shorter at 30". I may cut it shorter yet. I don't cut wide things that often. If I find myself doing it more, I might get one of those track saws Dan was talking about. Seems easier than feeding plywood through table saw.

Messages In This Thread

Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 2:30 pm
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 11/30/2014, 4:17 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 4:32 pm
Re: Strip: Cutting strips- track saw v table saw
Ken Blanton -- 11/30/2014, 5:55 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 5:59 pm
Re: Strip: Cutting strips- track saw v table saw *PIC*
JohnAbercrombie -- 11/30/2014, 6:10 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 6:21 pm
Re: Strip: Cutting strips- track saw v table saw *PIC*
Etienne Muller -- 11/30/2014, 7:20 pm
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 11/30/2014, 6:15 pm
Re: Strip: Cutting strips- track saw v table saw
Ken Blanton -- 11/30/2014, 6:22 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 6:27 pm
Re: Strip: Cutting strips- track saw v table saw
Marc Upchurch -- 11/30/2014, 6:45 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 11/30/2014, 6:55 pm
Re: Strip: Cutting strips- track saw v table saw
Gero Verheyen -- 11/30/2014, 7:17 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/1/2014, 1:08 am
Re: Strip: Cutting strips- track saw v table saw
John Messinger -- 12/2/2014, 6:33 am
Re: Strip: Cutting strips- track saw v table saw
Daniel Thaler -- 12/2/2014, 12:51 pm
Re: Strip: Cutting strips- track saw v table saw *PIC*
Jay Babina -- 12/2/2014, 1:20 pm
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 12/2/2014, 3:35 pm
Re: Strip: Cutting strips- track saw v table saw
Jay Babina -- 12/4/2014, 8:32 am
Re: Strip: Cutting strips- track saw v table saw *PIC*
JohnAbercrombie -- 12/2/2014, 3:51 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/3/2014, 1:58 am
Re: Strip: Cutting strips- track saw v table saw *PIC*
Nick Schade - Guillemot Kayaks -- 12/2/2014, 2:08 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 12/2/2014, 6:31 pm
Re: Strip: Cutting strips- track saw v table saw
Etienne Muller -- 12/2/2014, 7:03 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/3/2014, 2:01 am
Re: Strip: Cutting strips- track saw v table saw
Etienne Muller -- 12/3/2014, 4:51 am
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 12/3/2014, 6:17 am
Re: Strip: Cutting strips- track saw v table saw *PIC*
Rob Macks/Laughing Loon CC&K -- 12/3/2014, 10:00 am
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 12/3/2014, 12:41 pm
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/3/2014, 2:24 pm
Re: Strip: Cutting strips- track saw v table saw
wanderfalk -- 12/4/2014, 1:35 am
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/4/2014, 8:27 am
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/5/2014, 7:59 am
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/4/2014, 11:11 am
Re: Strip: Cutting strips- track saw v table saw
Robert Horstmann -- 12/4/2014, 11:59 am
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/4/2014, 1:28 pm
Re: Strip: Cutting strips- track saw v table saw *PIC*
Etienne Muller -- 12/4/2014, 3:13 pm
Re: Strip: Cutting strips- track saw v table saw
Daniel Thaler -- 12/3/2014, 12:56 pm
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/3/2014, 2:47 pm
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 12/3/2014, 6:51 pm
Re: Strip: Cutting strips- track saw v table saw
JohnAbercrombie -- 12/3/2014, 6:49 pm
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 12/3/2014, 8:58 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/3/2014, 4:50 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/4/2014, 1:03 am
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/4/2014, 8:50 am
Re: Strip: Cutting strips- track saw v table saw
Bill Mayberry -- 12/4/2014, 3:04 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/6/2014, 3:28 am
Re: Strip: Cutting strips- track saw v table saw
george jung -- 12/6/2014, 10:11 am
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 12/6/2014, 10:21 am
Re: Strip: Cutting strips- track saw v table saw
Dan Thaler -- 12/6/2014, 12:15 pm
Re: Strip: Cutting strips- track saw v table saw
Bill Hamm -- 12/6/2014, 3:30 pm
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/6/2014, 10:41 am
Re: Strip: Cutting strips- track saw v table saw
Nick Schade - Guillemot Kayaks -- 12/6/2014, 1:15 pm
Re: Strip: Cutting strips- track saw v table saw
Rob Macks/Laughing Loon CC&K -- 12/4/2014, 11:38 am
Re: Strip: Cutting strips- Time Lapse
Nick Schade - Guillemot Kayaks -- 12/4/2014, 6:36 pm
Re: Strip: Cutting strips- Time Lapse
Etienne Muller -- 12/5/2014, 4:26 am
Re: Strip: Cutting strips- Time Lapse
Dan Caouette (CSCWC) -- 12/5/2014, 8:57 am
Re: Strip: Cutting strips- Time Lapse
Nick Schade - Guillemot Kayaks -- 12/5/2014, 9:24 am
Re: Strip: Cutting strips- Time Lapse
Bill Hamm -- 12/5/2014, 8:08 am
Re: Strip: Cutting strips- Time Lapse *PIC*
Nick Schade - Guillemot Kayaks -- 12/5/2014, 8:42 am
Re: Strip: Cutting strips- Time Lapse
Bill Hamm -- 12/5/2014, 7:12 pm