Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: bead not coming out right on router
By:Jim777
Date: 11/2/2014, 5:04 am

It sounds like the strips are slightly thicker than 1/4". If you use the thick strips with the ridge, the joint will fit fine, but you'll do a lot of work to fair the strips down to flush. Moving the fence back may have eliminated the ridge, but only because the bit isn't cutting full depth. Strips with a flat spot are NG, because unless the gap is full of glue, you risk an air pocket. If the ridge on the thick strips is only very small, you'd be better off using those and fairing the ridge out than having a joint that doesn't fit properly. If the ridge is bigger, (and you have a surface planer) you could go ahead & cut the coves & beads, then plane all the strips a little thinner to save fairing work.

Messages In This Thread

Strip: bead not coming out right on router
Marc -- 11/2/2014, 12:40 am
Re: Strip: bead not coming out right on router
Jim777 -- 11/2/2014, 5:04 am
Re: Strip: bead not coming out right on router
Etienne Muller -- 11/2/2014, 7:12 am
Re: Strip: bead not coming out right on router
Marc Upchurch -- 11/2/2014, 9:12 am
Re: Strip: bead not coming out right on router
Bob Ten Eyck -- 11/2/2014, 10:58 am
Re: Strip: bead not coming out right on router
Jay Babina -- 11/2/2014, 5:36 pm
Re: Strip: bead not coming out right on router
Marc Upchurch -- 11/2/2014, 5:54 pm
Re: Strip: bead not coming out right on router
Dan Thaler -- 11/2/2014, 6:24 pm
Re: Strip: bead not coming out right on router
JohnAbercrombie -- 11/2/2014, 11:06 pm
Re: Strip: bead not coming out right on router
Etienne Muller -- 11/3/2014, 8:14 am
Re: Strip: bead not coming out right on router
Mike Bielski -- 11/5/2014, 8:36 am
Re: Strip: bead not coming out right on router
Marc Upchurch -- 11/3/2014, 8:22 am
Re: Strip: bead not coming out right on router
Triad -- 11/4/2014, 7:15 am
Re: Strip: bead not coming out right on router
Marc Upchurch -- 11/4/2014, 8:04 am
Re: Strip: bead not coming out right on router
Triad -- 11/4/2014, 8:28 am
Re: Strip: bead not coming out right on router
Bill Hamm -- 11/5/2014, 12:45 am
Re: Strip: bead not coming out right on router
Allan -- 11/5/2014, 1:59 am
Re: Strip: bead not coming out right on router
Bill Hamm -- 11/6/2014, 12:17 am
Re: Strip: bead not coming out right on router
Allan -- 11/6/2014, 3:57 am
Re: Strip: bead not coming out right on router
Dan Caouette (CSCWC) -- 11/6/2014, 7:46 am
Re: Strip: bead not coming out right on router
Bill Hamm -- 11/6/2014, 2:32 pm
Re: Strip: bead not coming out right on router
ddaniels -- 11/7/2014, 5:48 pm
Re: Strip: bead not coming out right on router
Bill Hamm -- 11/8/2014, 6:38 am