Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: coaming - no lip?
By:Bill Hamm
Date: 9/29/2011, 2:05 am
In Response To: Re: Strip: coaming - no lip? (Jeff Horton)

: Mine is 28" wide and in all be the shallowest water I am just
: not comfortable straddling it which is how I get in my boats. So
: I have to come in from one side and just haven't found a good
: way to do that. Getting in is easier than getting out for me.
: With the rod holders I can't sit on the back deck and then swing
: a leg out.

: There is a lot of personal choices in a fishing boat. I love the
: milk crate hatch in the back and the rod holders.
: I wanted taller sides so I could lean over and not worry about
: water coming into the boat landing a fish or pulling up an
: anchor. But you have to balance so that your not hitting you
: elbows either.
: In my kayak I find I have hold my rod a couple of inches higher
: than normal to clear the coaming. With the large opening it's
: not a problem and I love that. My shoulder would start to hurt
: after a while.
: I raised the seat height since I had the stability. I like sitting
: up a little higher when fishing.

: Thats just a few things I prefer.

Extended paddle on one side as an outrigger, it's how most kayakers enter their boats.

Bill H.

Messages In This Thread

Strip: coaming - no lip?
Bill VerSteeg -- 9/27/2011, 10:31 am
Re: Strip: coaming - no lip?
Bob Beaullieu -- 9/27/2011, 11:24 am
Re: Strip: coaming - no lip?
Al Edie -- 9/27/2011, 12:00 pm
Re: Strip: coaming - no lip?
Bill VerSteeg -- 9/28/2011, 8:56 am
Re: Strip: coaming - no lip?
Jay Babina -- 9/27/2011, 1:50 pm
Re: Strip: coaming - no lip?
Bill VerSteeg -- 9/28/2011, 8:53 am
Re: Strip: coaming - no lip?
Rob Macks / Laughing Loon CC&K -- 9/27/2011, 2:16 pm
Re: Strip: coaming - no lip?
Mike Bielski -- 9/27/2011, 3:01 pm
Re: Strip: coaming - no lip?
Al Edie -- 9/29/2011, 1:41 pm
Re: Strip: coaming - no lip?
Bill Hamm -- 9/29/2011, 3:51 pm
Re: Strip: coaming - no lip?
Al Edie -- 9/30/2011, 11:28 am
Re: Strip: coaming - no lip?
Bill Hamm -- 10/3/2011, 1:57 am
Re: Strip: coaming - no lip?
Al Edie -- 10/3/2011, 1:56 pm
Re: Strip: coaming - no lip?
Bill Hamm -- 10/4/2011, 2:36 am
Re: Strip: coaming - no lip?
Charles Robinson -- 9/27/2011, 5:39 pm
Re: Strip: coaming - no lip?
Bill Hamm -- 9/28/2011, 2:04 am
Re: Strip: coaming - no lip? *PIC*
Jeff Horton -- 9/28/2011, 2:28 pm
Re: Strip: coaming - no lip?
Bill VerSteeg -- 9/28/2011, 2:37 pm
Re: Strip: coaming - no lip?
Jeff Horton -- 9/28/2011, 4:01 pm
Re: Strip: coaming - no lip?
StephenHJ -- 9/28/2011, 4:24 pm
Re: Strip: coaming - no lip?
Bill Hamm -- 9/29/2011, 2:05 am