Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Firestar Upper Bow Piece
By:Bill Hamm
Date: 3/10/2011, 7:15 pm
In Response To: Re: Strip: Firestar Upper Bow Piece (ancient kayaker)

: Further thoughts:

: The importance of sharp tools cannot be exaggerated. A really sharp
: chisel will produce a fine surface - as good as a plane. To get
: an extra fine cut use your right (left) hand to hold and control
: the chisel and use the left (right) thumb to slide the edge
: sideways as it slices off an almost transparent paring. This
: gives you great control.

: A sharp edge lasts longer as there is less stress on the edge
: material. If the chisel comes with an edge protector use it; if
: not make one from a piece of wood with a slot in it. Chisels are
: delicate - don’t store them close to files and other
: “ruffian” tools. Don’t let any edged tool get blunt - it
: takes a more work to get them sharp again than it does to keep
: them that way. Chisels are like plane blades: for curly -or
: cross-grain sharpen the chisel at a shallower angle. For heavy
: work use a coarser angle.

: For making guide cuts for small mortises I use a dowel cutoff saw;
: I clamp a block at the line and use the saw with the non-marring
: side toward the block - very precise.

: A routing table is also handy for rabbets. However, if you use an
: outer or false stem the rabbet for the planking is not required,
: but the stem dimensions will change.

: An inexpensive and very useful rasp for a quick fix is the
: “four-in-one” - it has a round and a flat side and both fine
: and course surfaces. It can be rough on the hands so I have
: others that are better for extended use but this is the one I
: use the most. Lee Valley Tools sell it among others.

: On the subject of (handheld) belt sanders, I very rarely use mine
: since I acquired a bench-mounted combined belt and disc sander.
: Much more accurate. For scarfing thin strips I now use the disc
: sander with a guide clamped to the table; it is quicker and more
: accurate than anything else I have tried including a plane, a
: chop saw and a router, and the sander needs no jig. When using
: the belt for thin pieces wear leather gloves and always install
: the projectile catcher that comes with the tool!

Leather glove eliminate all the fun of sanding off your fingerprints .

Bill H.

Messages In This Thread

Strip: Firestar Upper Bow Piece
Stephen Troy -- 3/7/2011, 2:02 pm
Re: Strip: Firestar Upper Bow Piece
Mike Savage -- 3/7/2011, 3:25 pm
Re: Strip: Firestar Upper Bow Piece
Mark Joyse -- 3/7/2011, 5:01 pm
Re: Strip: Firestar Upper Bow Piece *PIC*
Clayton Plunkett -- 3/7/2011, 7:29 pm
Re: Strip: Firestar Upper Bow Piece
Kurt Maurer -- 3/7/2011, 7:39 pm
Thanks! Where to buy...
Stephen Troy -- 3/8/2011, 3:41 pm
Re: Thanks! Where to buy...
Mark Joyse -- 3/8/2011, 3:51 pm
Re: Thanks! Where to buy...
Kurt Maurer -- 3/8/2011, 3:55 pm
Re: Thanks! Where to buy...
Bill Hamm -- 3/9/2011, 12:52 am
Re: Thanks! Where to buy...
Bill Hamm -- 3/9/2011, 12:54 am
Re: Strip: Firestar Upper Bow Piece *PIC*
Rob Macks / Laughing Loon CC&K -- 3/7/2011, 8:23 pm
Re: Strip: Firestar Upper Bow Piece
Darel -- 3/7/2011, 9:45 pm
Re: Strip: Firestar Upper Bow Piece
Bill Hamm -- 3/8/2011, 12:22 am
Re: Strip: Firestar Upper Bow Piece
Mike Bielski -- 3/8/2011, 7:41 am
Re: Strip: Firestar Upper Bow Piece
ancient kayaker -- 3/10/2011, 7:04 pm
Re: Strip: Firestar Upper Bow Piece
Bill Hamm -- 3/10/2011, 7:15 pm
Re: Strip: Firestar Upper Bow Piece
ancient kayaker -- 3/10/2011, 10:11 pm
Re: Strip: Firestar Upper Bow Piece
Bill Hamm -- 3/11/2011, 7:12 am
Re: Strip: Firestar Upper Bow Piece
Bill Hamm -- 3/11/2011, 7:14 am
Re: Strip: Firestar Upper Bow Piece
ancient kayaker -- 3/11/2011, 9:22 am
Re: Strip: Firestar Upper Bow Piece
StephenHJ -- 3/18/2011, 2:01 am