Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Another workbench/strongback/buffet idea
By:Bill Hamm
Date: 2/25/2011, 7:16 am
In Response To: Re: Another workbench/strongback/buffet idea (Randy Echtinaw)

: I have two similar tables 36"x8'. One has lockable swivel
: castors and the other has 1/2" bolts with Pal nuts in the
: legs to adjust for any uneven cement in my shop. Each has a full
: shelf about 8" from the floor. When tables are positioned I
: drop a bag of ready-mix cement at each end of the shelf of each
: table, makes them very solid. Both tables, my table saw, with
: hinged extension, and work bench are all the same height - very
: comfortable:)
: Randy

Actually those would be very handy here, though I'll have to think about being able to fold the table top in half so can use as extension tables on the bandsaw (with a 3' wide table I couldn't reach the saw ).

Everything except the workbench is on wheels here, makes it easy to gain floor space.

Btw, my workbench is three Craftsman workbench bases joined to form a 12' bench. I'm going to be using a two by top under the particle board to make them more rigid. Going to trim 2x4's to eliminate the rounded edge they normally have, probably trim them to 1 1/2" x 3" then glue them together to form a rigid base for the actual top. The particle board surface has a much higher impact strength than the MDF everyone seems to like. The top will then be 3/4" ply, with a 1 1/2" softwood middle and a 3/4" particle board surface, should be fairly rigid ;)

Bill H.

Bill H.

Messages In This Thread

Shop: Workbench Progress
Noel Bennett -- 2/21/2011, 11:06 pm
Re: Shop: Workbench Progress
Bill Hamm -- 2/22/2011, 1:06 am
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 9:01 am
Re: Shop: Workbench Progress
Paul G. Jacobson -- 2/22/2011, 1:16 am
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 8:55 am
Re: Shop: Workbench Progress *PIC*
Paul G. Jacobson -- 2/22/2011, 5:54 pm
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 11:32 pm
Another workbench/strongback/buffet idea *PIC*
Paul G. Jacobson -- 2/23/2011, 6:38 pm
And folding legs for that *PIC*
Paul G. Jacobson -- 2/23/2011, 6:49 pm
Re: And folding legs for that
Noel Bennett -- 2/23/2011, 11:09 pm
Re: And folding legs for that
dhwdaniels -- 2/24/2011, 3:01 pm
Re: Another workbench/strongback/buffet idea
dhwdaniels -- 2/24/2011, 3:00 pm
Re: Another workbench/strongback/buffet idea
Paul G. Jacobson -- 2/24/2011, 3:06 pm
Re: Another workbench/strongback/buffet idea
Randy Echtinaw -- 2/25/2011, 5:53 am
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/25/2011, 7:16 am
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/25/2011, 7:20 am
Re: Another workbench/strongback/buffet idea
Paul G. Jacobson -- 2/25/2011, 3:35 pm
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/26/2011, 12:29 am
Re: Shop: Workbench Progress
Dean -- 2/23/2011, 10:16 am
Re: Shop: Workbench Progress
Will N To Go -- 2/23/2011, 11:24 pm
Re: Shop: Workbench shelf idea *PIC*
Paul G. Jacobson -- 2/22/2011, 5:57 pm
Re: Shop: Workbench Progress
Eric -- 2/22/2011, 11:16 am
Re: Shop: Workbench Progress
Will N To Go -- 2/23/2011, 11:34 pm
Re: Shop: Workbench Progress
Paul G. Jacobson -- 2/24/2011, 3:54 am
Re: Shop: Workbench Progress
Bill Hamm -- 2/24/2011, 6:28 am
Re: Shop: Workbench Progress
TheLuckyOne -- 3/14/2011, 12:03 am