Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Shop: Workbench Progress
By:Bill Hamm
Date: 2/24/2011, 6:28 am
In Response To: Re: Shop: Workbench Progress (Will N To Go)

: Another thought for a strong flat work bench.
: All the designs here use 2x4s and 2x6s. 2x6's vertical joists are
: probably overkill for a work surface. 2x6 16" on center
: could probably support 3000+ pounds.
: 2x4s are plenty. You could, it carefully constructed use 1x4
: material.

: In a floor joist with solid blocking between the joists, current
: testing I've red about in FineHomebuilding mag rates it almost
: as high as if uncut joists were running in both 90 degree
: directions.

: I think I'd rip some 2x3s or 4's on my table saw (to make 1x3s or
: 1x4s) lay down a sheet of medium density fiberboard the size I
: want for the top. Make sure it's flat and level.
: Cut all my 'joists' and blocking, then mix up all the old epoxy
: I've got laying around, add a little filler (or pancake mix) to
: thicken it, then glue it all together.
: A coat of sealer and it will be flat and strong for a hundred
: years.
: for legs I'd just make some really solid saw horses. The only way
: I'd add regular legs is if it was to be in one permanent spot,
: and I wanted storage underneath.

The top of any work bench, even hardwood, will eventually get nicked up, one advantage of using sheet goods for the top is if it's screwed down, the top pieces can be taken off and flipped over when they get too beat up to use, then for free you get a brand new work surface.

Putting the underlying boards together with glue, I use carpenter's glue works just as well for this and is cheaper, is a good idea though.

Bill H.

Messages In This Thread

Shop: Workbench Progress
Noel Bennett -- 2/21/2011, 11:06 pm
Re: Shop: Workbench Progress
Bill Hamm -- 2/22/2011, 1:06 am
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 9:01 am
Re: Shop: Workbench Progress
Paul G. Jacobson -- 2/22/2011, 1:16 am
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 8:55 am
Re: Shop: Workbench Progress *PIC*
Paul G. Jacobson -- 2/22/2011, 5:54 pm
Re: Shop: Workbench Progress
Noel Bennett -- 2/22/2011, 11:32 pm
Another workbench/strongback/buffet idea *PIC*
Paul G. Jacobson -- 2/23/2011, 6:38 pm
And folding legs for that *PIC*
Paul G. Jacobson -- 2/23/2011, 6:49 pm
Re: And folding legs for that
Noel Bennett -- 2/23/2011, 11:09 pm
Re: And folding legs for that
dhwdaniels -- 2/24/2011, 3:01 pm
Re: Another workbench/strongback/buffet idea
dhwdaniels -- 2/24/2011, 3:00 pm
Re: Another workbench/strongback/buffet idea
Paul G. Jacobson -- 2/24/2011, 3:06 pm
Re: Another workbench/strongback/buffet idea
Randy Echtinaw -- 2/25/2011, 5:53 am
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/25/2011, 7:16 am
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/25/2011, 7:20 am
Re: Another workbench/strongback/buffet idea
Paul G. Jacobson -- 2/25/2011, 3:35 pm
Re: Another workbench/strongback/buffet idea
Bill Hamm -- 2/26/2011, 12:29 am
Re: Shop: Workbench Progress
Dean -- 2/23/2011, 10:16 am
Re: Shop: Workbench Progress
Will N To Go -- 2/23/2011, 11:24 pm
Re: Shop: Workbench shelf idea *PIC*
Paul G. Jacobson -- 2/22/2011, 5:57 pm
Re: Shop: Workbench Progress
Eric -- 2/22/2011, 11:16 am
Re: Shop: Workbench Progress
Will N To Go -- 2/23/2011, 11:34 pm
Re: Shop: Workbench Progress
Paul G. Jacobson -- 2/24/2011, 3:54 am
Re: Shop: Workbench Progress
Bill Hamm -- 2/24/2011, 6:28 am
Re: Shop: Workbench Progress
TheLuckyOne -- 3/14/2011, 12:03 am