Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: How to store hull?
By:Bill Hamm
Date: 2/16/2011, 9:27 am
In Response To: Re: Strip: How to store hull? *PIC* (Etienne Muller - ireland)

: The above is the optimum solution. You can do this with an external
: strong-backs too. Ie: leave the forms in the boat. Let the boat
: be the strong-back after it is turned over (see picture). Of
: course one has to remove staples and nails so that sanding and
: glassing can be done. I do the outside of the hull - turn the
: hull over - leave the inside rough - reinsert the forms in their
: slots, put a tack in at the hull sheer-strip to hold them in
: place (this tiny hole is covered when the sheer is glassed
: later) (one could use hot glue too) - strip the deck.

: One could also leave the hull rough while doing the deck and glass
: the whole shebang afterwards, but glassing the hull outside
: before turning gives the hull some stiffness and ding resistance
: while one is working on and sanding the deck.

: Many participants in this forum will be bored of me stating the
: following, but for the newer builders here; consider glassing
: the inside of the hull, joining it to the deck, and then
: glassing the outside and taping the hull/deck join at the same
: time with the decking cloth. The benefits of this are more
: flexibility in the deck for joining and a quicker cleaner cloth
: join at the sheer as tape is not required. (the deck cloth does
: the job). This method is easy for boats with a hard angle at the
: sheer like the one pictured, as one can use a sheer-clamp,
: rather than those that are joined in a flatter section. But it
: will work with these too if care is taken. The downside is that
: if one is cutting out the openings before joining the halves the
: deck becomes very fragile. With a sheer-clamp one can cut the
: openings after the deck is installed. If one is taping this is
: possible too, but ideally after the hull and deck are joined and
: finished outside, then one can reach inside through the hatch
: cutouts to do the inside taping.

: To see the above method

: http://www.etiennemuller.com/northstar/pages/0039.html

: then keep clicking on the forward arrow to see the process.

: I have always built my boats as described because I began building
: in an era before the wide availability of proper plans and
: instructions and just did what seemed most logical in any
: situation. For nervous first-timers this may be too much of a
: deviation from the instructions that came with your plans. Worth
: consideration for a second build though.

: Et

Hi Et,

Just had a thought (yeah I know, dangerous) but when cutting out the forms, one could use the remaining cut-out for a sort of reverse form to make a really nice cradle for the hull. The cut out would have to be opened up a bit to allow for the strips and the glass but that would be fairly easy and you'd not need every form, perhaps every fourth. You could then with an external strongback remove the male forms and replace with those that would fit in the same exact location to very nicely support the hull while the deck is built. Would keep the hull from changing shape in any way.

Bill H.

Bill H.

Messages In This Thread

Strip: How to store hull?
Paul Lueders -- 2/14/2011, 6:27 pm
Re: Strip: How to store hull?
Ric Moodie -- 2/14/2011, 7:03 pm
Re: Strip: How to store hull?
Paul Lueders -- 2/14/2011, 7:10 pm
Re: Strip: How to store hull? *PIC*
Farback -- 2/14/2011, 8:04 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/15/2011, 2:00 am
Re: Strip: How to store hull?
Ian Johnson -- 2/15/2011, 7:59 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/16/2011, 12:45 am
Re: Strip: How to store hull?
Randy Echtinaw -- 2/15/2011, 8:21 am
Re: Strip: How to store hull?
Allan -- 2/15/2011, 8:26 pm
Re: Strip: How to store hull? *PIC*
Etienne Muller - ireland -- 2/16/2011, 6:18 am
Re: Strip: How to store hull?
Bill Hamm -- 2/16/2011, 9:27 am
Re: Strip: How to store hull?
Etienne Muller - ireland -- 2/17/2011, 5:05 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/17/2011, 7:12 pm
Re: Strip: How to store hull?
Les Cheeseman -- 2/18/2011, 11:04 am
Re: Strip: How to store hull?
Bill Hamm -- 2/18/2011, 2:07 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/18/2011, 2:09 pm
Re: Strip: How to store hull?
Farback -- 2/17/2011, 10:31 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/18/2011, 9:59 am
Re: Strip: How to store hull?
Kirk Fredericks - Farback Carpentry and Automation -- 2/18/2011, 12:47 pm
Re: Strip: How to store hull?
Bill Hamm -- 2/18/2011, 2:08 pm