Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: Ripping better strips
By:Phil Nelson
Date: 1/18/2011, 4:17 pm
In Response To: Re: Strip: Ripping better strips (ancient kayaker)

The second fence is just lightly pushed against the plank, other wise it will get tight. Set your second fence, nip the clamps up, lift the blade on the saw & do a quick trial run down the plank to check for tight spots. Adjust it if you find it binds then tighten the clamps properly.

Good tip for dealing with narrow pieces !

: I prefer to use a single guide but I have to ensure the leading
: edge stays in contact with the wood: I would worry that using 2
: guides could result in a jam.

: Some additional notes: When ripping narrow strips the guide should
: be outboard of the blade - a metal guide works well. A wider
: tee-shaped ply guide on the inboard side can be used for wider
: pieces. When ripping the last few strips from a plank that is
: getting very narrow, the plank can be attached to another plank
: with double-sided tape or even glued - waste not, want not ...

Messages In This Thread

Strip: Ripping better strips
Stephen Troy -- 1/15/2011, 11:29 pm
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 12:53 am
Re: Strip: Ripping better strips
Al Edie -- 1/16/2011, 3:19 am
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 3:27 am
Re: Strip: Ripping better strips
Al Edie -- 1/16/2011, 3:38 am
Re: Strip: Ripping better strips
Bill Hamm -- 1/16/2011, 7:04 am
Re: Strip: Ripping better strips
Tony Olsen -- 1/16/2011, 9:02 am
Re: Strip: Ripping better strips
Mike Savage -- 1/16/2011, 12:42 pm
Re: Strip: Ripping better strips
Paul G. Jacobson -- 1/16/2011, 1:37 pm
Re: Strip: Ripping better strips
Ken Blanton -- 1/16/2011, 5:55 am
Re: Strip: Ripping better strips
Jay Babina -- 1/16/2011, 9:01 am
Re: Strip: Ripping better strips
Ian Cummins -- 1/16/2011, 5:08 pm
Re: Strip: Ripping better strips
Kurt Maurer -- 1/16/2011, 7:23 pm
Re: Strip: Zen
Ian Johnson -- 1/16/2011, 8:08 pm
Re: Strip: Ripping better strips
Kirk Fredericks -- 1/16/2011, 10:49 pm
Re: Strip: Ripping better strips
Tony Olsen -- 1/16/2011, 10:58 pm
Re: Strip: Ripping better strips
Kirk Fredericks -- 1/16/2011, 11:04 pm
Re: Strip: Ripping better strips
Paul G. Jacobson -- 1/16/2011, 9:10 pm
Re: Strip: Ripping better strips
Phil Nelson -- 1/16/2011, 10:03 pm
Re: Strip: Ripping better strips
ancient kayaker -- 1/18/2011, 10:39 am
Re: Strip: Ripping better strips
Phil Nelson -- 1/18/2011, 4:17 pm
Thanks all
Stephen Troy -- 1/17/2011, 12:31 am
Re: Thanks all
Paul G. Jacobson -- 1/17/2011, 4:02 am
Re: Thanks all
Bill Hamm -- 1/17/2011, 6:43 am
Featherboard use *PIC*
Paul G. Jacobson -- 1/17/2011, 6:50 pm
Re: Featherboard use
Les Cheeseman -- 1/20/2011, 9:54 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:08 am
Re: Featherboard use
Les Cheeseman -- 1/20/2011, 11:28 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:13 am
Re: Featherboard use
Bill Hamm -- 1/20/2011, 10:32 am
Re: Thanks all
Les Cheeseman -- 1/19/2011, 9:18 am
Re: Thanks all
Bill Hamm -- 1/19/2011, 9:28 am
infeeed.outfeed table extensions.
Paul G. Jacobson -- 1/19/2011, 8:00 pm
And the picture for that is--- *PIC*
Paul G. Jacobson -- 1/19/2011, 8:06 pm
Re: And the picture for that is---
Bill Hamm -- 1/19/2011, 8:52 pm
Re: And the picture for that is---
Bill Hamm -- 1/19/2011, 8:58 pm
Re: And the picture for that is---
Les Cheeseman -- 1/20/2011, 9:47 am
Re: And the picture for that is--- *PIC*
Etienne Muller - ireland -- 1/20/2011, 4:39 pm
Re: And the picture for that is---
Les Cheeseman -- 1/21/2011, 3:54 am
Re: Strip: Ripping better strips
Etienne Muller - ireland -- 1/17/2011, 5:07 am