Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Epoxy: Heat for glassing
By:Mike Savage
Date: 12/1/2010, 2:16 pm
In Response To: Epoxy: Heat for glassing (Palle Dam)

: I am building in an uninsulated garage and will have to heat it to
: do the glassing. I plan to build some kind of tent around the
: kayak to minimize the space to be heated.
: But heating is expensive. How long is it necessary to heat? How
: much should the epoxy cure before I can turn of the heat? I'm
: not looking for a number of hours (Because it varies between the
: different epoxy-brands), more like at which cure-stage I can
: stop heating.
: The temperature is around freezing at the moment. Without the tent
: (which I haven't made yet) I could only get the temperature up
: to around 14 C (~57 F) with a 2000 W electric heater and a 4200
: W propane heater. But that is too expensive for long term use.
: Btw. does anyone have a description or pictures of a tent-frame
: that is easy to make?

: Palle Dam
: Denmark

Hi Palle,
Can't really help with the timing, I've only used epoxy in summertime, or not in winter. But the tent is an easy one. For inside a garage, a simple rigid pvc piping frame will do fine covered by a double or triple layer of the clear plastic used for growing tunnels. If it's just for keeping heat around the hull, have it about a foot (30cm) out each side of the hull and it can be the same above the hull. A series of incandescent lights beneath the hull will keep the enclose volume quite warm. A simple box shaped tent will work. If you gang the lights in 5 lights per switch, you can control how hot it gets. I think less than 2000 watts worth will do.

5 uprights per side, an elbow joiner on each and 5 pieces for the 'roof'. Lengthwise pipes can be tied or duck taped to these as stringers. A few diagonal pieces will make it less wobbly. Drape the doubled plastic over the frame over the hull. If you want more insulation, light blankets could be added.

I thought I had drawings for one of these (probably on my dead PC) but I mostly freehand something as temporary as this.

Hope this is some help,
Mike Savage
South West Cork

The past week, my workshop/garage* has reached the 15C level a few times, mostly hovering about 12C. And that's with it's central heating circuit working. Mind you, it drops to -3C outside with the present Arctic weather we've got this end of Europe, similar to Denmark's weather, warmer than Berlin. :)
*Used to be a carport/garage, got converted to a summer apartment then to a workshop.

Messages In This Thread

Epoxy: Heat for glassing
Palle Dam -- 12/1/2010, 8:32 am
Re: Epoxy: Heat for glassing
Don Flowers -- 12/3/2010, 2:02 pm
Re: Epoxy: Heat for glassing
Palle Dam -- 12/4/2010, 1:18 pm
Re: Epoxy: Heat for glassing
Bill Hamm -- 12/6/2010, 12:19 am
Re: Epoxy: Heat for glassing
Bill Hamm -- 12/6/2010, 12:16 am
Re: Epoxy: Heat for glassing
Al Edie -- 12/5/2010, 6:36 pm
Re: Epoxy: Heat for glassing
Les Cheeseman -- 12/2/2010, 1:31 pm
Re: Epoxy: Heat for glassing
Mike Savage -- 12/1/2010, 2:16 pm
Re: Epoxy: Heat for glassing
Bill Hamm -- 12/1/2010, 6:06 pm
Re: Epoxy: Heat for glassing
Bill Hamm -- 12/1/2010, 1:43 pm
Re: Epoxy: Heat for glassing
Ric -- 12/1/2010, 11:48 am