Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Kayak cart
By:Alex Ferguson
Date: 8/15/2001, 9:56 pm
In Response To: Re: Kayak cart (Dale Frolander)

: I'm not sure what the T-bar design is. I was thinking I could build a cart,
: but I wanted one for R2K1 and don't have the time right now.

Providing you have wheels available (take the same time to buy those as a whole cart?), the rest is simple.

I designed the "T"bar trolley a while ago and its design has "taken off" in parts of this country.

Basically there are two "Ts" in parallel, with an axle joining them. The axle goes through the bottom of the vertical bar of the "T". The kayak fits between/on the parallel tops of the "Ts" Make the distance between the "Ts" a bit less than the width of the kayak at a point halfway between cockpit and stern.

I've made the "Ts" out of welded aluminium and used PVC water pipe. If using PVC, buy a couple of "T" pieces and extend the length of the horizontal and vertical. Use 50 mm high pressuse piping. The extension bits are actually quite short so strength isn't of a concern. The axle (1/2" stainless steel tube) should have a length of plastic pipe on it to keep the "Ts" apart and "R" pins or similar to keep the wheels on and make it easy to dismantle.

The kayak is held on the trolley by a couple of webbing straps with quick release buckles (Fastex TM). I cross them under the bars of the trolley and crossed on the deck. If you wished you can cut holes in the ends of the T bars and feed the straps through (no crossing over).

The height of the "Ts", the tops should be level or slightly below the tops of the wheels (kayak bottom curve should make it clear the wheels if the tops are lower).

Broken down, you have 2 "Ts", 1 axle, 2 straps, 2 wheels which should find a home somewhere though on a multiday trip I usually start with parts of the cart on deck until I've "eaten" my way some way through the kayak.

One final refinement, "legs". A notch in the bottom at one end of each horozontal of the "Ts". A piece of stiff nylon tube or similar equal the distance from the bottom of the horizontal to the ground. Bungy, stretched from the ground end of the "leg" (inside the leg), through the notch to the far end of the inside of the horizontal. This is the leg "down". If taken out of the notch the leg should disappear into the horizontal of the "T" as the bungy "retracts" the leg. When down, these keep the cart level for loading and they will sometimes retract automatically when you tow the kayak, doesn't matter if thhey don't.

If there are still some parts unclear, e-mail me.

Alex
.
.

Messages In This Thread

Kayak cart
Dale Frolander -- 8/14/2001, 6:22 pm
Re: Kayak cart
Alex Ferguson -- 8/14/2001, 9:17 pm
Re: Kayak cart
Dale Frolander -- 8/15/2001, 2:08 pm
Re: Kayak cart
Alex Ferguson -- 8/15/2001, 9:56 pm
Re: Kayak cart
Dale Frolander -- 8/16/2001, 2:18 pm
Kayak cart compaction.
mike allen -- 8/16/2001, 12:34 am
Compaction: I like it! *NM*
Shawn Baker -- 8/16/2001, 9:53 am
Re: Kayak cart compaction.
Alex Ferguson -- 8/16/2001, 1:04 am
Re: Kayak cart compaction.
mike allen -- 8/16/2001, 12:05 pm
another mistake
mike allen -- 8/16/2001, 12:18 pm
forgot to say
mike allen -- 8/16/2001, 12:13 pm
Looks like a folding camp stool, with wheels
Paul G. Jacobson -- 8/14/2001, 8:39 pm